1. <s id="ssgb2"><object id="ssgb2"><blockquote id="ssgb2"></blockquote></object></s>
      2. <button id="ssgb2"></button><span id="ssgb2"></span>
      3. <s id="ssgb2"></s>

          <th id="ssgb2"></th>
          <em id="ssgb2"><acronym id="ssgb2"><u id="ssgb2"></u></acronym></em>
          <tbody id="ssgb2"></tbody>

          <legend id="ssgb2"><pre id="ssgb2"></pre></legend>

          1. 杭州順德鋸業有限公司是多片鋸生產廠家,主營:杭州多片鋸、多片鋸品牌、多片鋸鋸片、多片鋸銷售、多片鋸價格等!
            新聞 中心
            • 焊齒在合金鋸片上是怎么樣一個存在?
            • 本站編輯:杭州順德鋸業有限公司發布日期:2018-06-29 12:31 瀏覽次數:
            合金鋸片焊齒的操作步驟
            Operation procedure of alloy saw blade welding
            305-3.2-2.2-25.4-120
            合金由超細微粉在高壓內完成燒結溫度在1200℃,現在合金焊接都偏向低溫焊接。目的保護其金相組織在焊接時不受到破壞,焊接溫度不宜高于750℃,溫度均勻比較好隔齒焊接。
            The alloy is made of ultrafine powder at high pressure. The sintering temperature is 1200 degrees. Now the alloy welding is biased towards low temperature welding. Objective to protect the metallographic structure from being damaged during welding, and the welding temperature should not be higher than 750 degrees.
            焊齒時要注意合金是否有碳化物,保持合金周邊干凈不要有灰塵,齒座不允許有銹點或氧化物,助焊劑不宜太濃或太稀,調成糊狀,有粒狀助焊劑不能使用。注意沉淀,重復使用時要調和助焊劑,比較好滴在合金上,不要糊在基體齒根外。
            When welding teeth, we should pay attention to whether the alloy has carbides, keep the alloy around clean and do not have dust, the teeth are not allowed to have rust or oxide, and the flux should not be too thick or too thin to make a paste, and the granular flux can not be used. Attention should be paid to precipitation. When used repeatedly, the flux should be reconciled, preferably on the alloy, not on the root of the matrix.
            使用銀焊絲不能追求含銀量過高,一般在45%就可以。銀焊絲主要金屬元素銀、銅、鎳,銀低溫,鎳鋅增強流動性,銅增加強度,只要增加適量錳、銦、硒,粘結力更強。錳有氣孔,銦、硒元素太貴,一般焊絲焊接強度每平方厘米強度為5-16KG,一般每個齒視合金焊接面積大小而定,每齒強度不能低于50KG,工業類型在100KG以上。
            The use of silver wire can not pursue excessive silver content, usually in 45%. Silver, copper, nickel, silver and nickel are the main elements of silver welding wire. The fluidity of nickel and zinc is enhanced, and the strength of copper is increased. As long as the amount of manganese, indium and selenium are increased, the cohesive force is stronger. Manganese has stoma, indium and selenium is too expensive, the strength of welding wire welding is 5-16KG per square centimeter. In general, the size of each tooth alloy welding area depends on the strength of each tooth. The strength of each tooth can not be less than 50KG, and the industrial type is above 100KG.
            焊完鋸片后隨即放在100℃烘箱內回火,減少焊齒造成應力及細化合金內部組織,提高耐用及耐磨度。
            After welding the saw blade, it will be tempered in the oven at 100 degrees Celsius to reduce the stress caused by the welding tooth and to refine the internal structure of the alloy, so as to improve durability and wear resistance.

                1. <s id="ssgb2"><object id="ssgb2"><blockquote id="ssgb2"></blockquote></object></s>
                2. <button id="ssgb2"></button><span id="ssgb2"></span>
                3. <s id="ssgb2"></s>

                    <th id="ssgb2"></th>
                    <em id="ssgb2"><acronym id="ssgb2"><u id="ssgb2"></u></acronym></em>
                    <tbody id="ssgb2"></tbody>

                    <legend id="ssgb2"><pre id="ssgb2"></pre></legend>

                    1. 韩国V欧美V亚洲V日本V_韩国A片大全免费看片_亚洲妇女自偷自偷图片_久久精品国产久精国产